How to Do a Door Lock Change
Change your door lock is a simple and affordable way to improve the security of your home. However, this process is not for everyone. It requires some expertise and perseverance.
The cylinder is inside the knob body. The cylinder is what identifies the key when it's inserted into the lock.
Take off the lock that was previously used.
The first step to replace a door lock is to get rid of the old lock. It's a relatively straightforward process, however it is important to keep a few things in mind. Make sure that the new lock is compatible with your door. This will ensure that it fits securely and does not leave a gap in the deadbolt plug or latch.
After removing the latch plate, you will need to look for two bolts or screws on the inside of the casing that hold the casing in place with the lock halves. Unscrew them using the help of a screwdriver, and then remove the lock from the door. If you have a mortise lock, there could be a set screw located at the base of the handle, which binds it to the spindle. Use a screwdriver to remove this screw, then pull out the doorknobs.
Remove the deadbolt and latch plug from your door jamb. Install the new lock. If you're replacing a mortise, you must determine the distance between your lock case and your door's edge to make sure that your new lock fits.
You may want to replace your lock for a variety of reasons, such as if you suspect that someone else holds the key or you have new roommates. In any case, you can save money by taking the lock off yourself, rather than hiring an expert to remove it. It's easier than many people think and can be done in a few minutes.
Begin by removing the trim and handle from the door. With a flat screwdriver take off the trim. You should be able to twist off most of it, and in some instances the handles may fall off entirely. Then, check the handle for a tiny pinhole on the inside. Then insert a straightened clip into it. This will activate the release mechanism and allow you to remove the handle from the door. Next, examine the interior side of the lock for a small tab that you can press with a flat screwdriver. Once the spindle is removed, you can remove the housing and the cylinder.
The process of selecting a new lock
There are a lot of options available when it comes time to pick a new lock. Think about the various kinds of locks and choose one that is in keeping with the design of your door. Take into consideration the backset which is the distance between the edge and the center of the hole for the lock. Also, consider the cross bore, a tiny hole that is located at the edge of your door's frame. Choose a lock that fits the door thickness and the swing.
The American National Standards Institute and BHMA have graded the majority of locks for doors to give you an idea of their strength and how difficult it is to pick them or disable them. A lock of grade 3 could be perfect for a quiet apartment complex in the countryside, whereas locks of grade 1 might be more appropriate for an area with a lot of traffic, such as the storefront.
Most smart door locks require digital code to open. If you are concerned about hacking, or other security issues, talk to a professional locksmith.
Replacing the cylinder
You can easily replace damaged or broken door lock cylinder by doing an easy DIY project. The key is to select the right cylinder, and follow the instructions that are included with it. First, you must remove the knob or handle, if it is present. Then with a screwdriver take off the trim around the lock cylinder. Once the trim is removed, you will be able to access the screws that keep the cylinder in place and remove them using a flathead screwdriver. The cylinder can then be gently removed from the door.
Before installing the new cylinder, be sure that it's the right length for your door. With an instrument, measure the distance between the center of the cylinder and the right and left sides. Purchase a new cylinder which has the same measurements. This will prevent the cylinder from snapping, which can occur when the door is kicked out or when the key gets stuck inside.
If you have a suitable replacement cylinder, place it into the door and turn the key. This will ensure that the cylinder is in alignment with the carrier, which is normally located on the outside of the lock. Then, loosen the set screws, which should be a couple of turns in the head. double glazed window lock repair will also need to loosen the screw at the edge of the door that fastens the case, in the event that there is one.
After removing the lock cylinder, you can replace it with the new lock by sliding the new cylinder into the case and tightening the set screw. You must also install the bracket that connects the cylinder with the stem for the lock indicator and this can be done by pulling up three tabs on the back of the cylinder with needle-nose pliers. Then, you can attach the smaller bracket to the back of the cylinder. You must then install the strike plate and latch plate, as well as the retaining rings that are attached to the top of the lock cylinder.
Installing the new lock
Begin by measuring the door's width if you are replacing an existing lock. Most locksets for residential use are designed to fit a door thickness of 1 3/8 to 3/4 inch. If your door is thicker than 1 3/8 to 1 3/4 inches, you'll need a stronger door kit. This would include longer screws as well as an extension for the spindle or a longer tail piece for door knobs.
The majority of locks come with a comprehensive instruction booklet that will help you install the new hardware. Be sure to read the instructions thoroughly before beginning the process to ensure that you are following all the steps. The booklet will give you a clear idea of the level of skill that is required to finish the task. You might want to ask a friend who has worked with locks for assistance if you are changing locks for the first time.
Before installing the new lock it's recommended to cover the openings with tape the old hardware. This will stop the screws from falling through the holes, and also protect any tiles you may have installed. It also helps prevent potential damage from rust, grime, dirt and. SECURAM Touch comes with a strip painter's tape designed to be used to protect your painter's tape, but you can also use gaffer's or masking tape when you have it.
After you have removed the screws that hold the lock's inner half to its exterior, take the lock off immediately. It is important to do this as quickly as possible to prevent the lock from accidentally closing itself and damaging the mechanism.
If the new lock comes with an internal latch bolt, insert the new bolt into the upper cross bore. Make sure you place it in the correct place, which is usually indicated by an illustration on the faceplate. Then, screw the latch plate onto the bolt.
Screw the deadbolt to the jamb of the door. Test the deadbolt by throwing it a few times to ensure that it is extended all the way into the strike plate and is fully secure. Follow the instructions included with your electronic smart lock to program it. This involves downloading an app, registering your email address, verifying your identity, and then connecting to the wireless network to add your device.